Solutions For A Wet Basement

While preparing fora renovation of your basement, the initial problem which must be taken into account is moisture.

Remedies may be as simplistic as extending or rerouting your drain spout, or as costly as putting in perimeter drains. However vast that your water problems are, you should arm yourself with expert knowledge offered by our wet basement solutions in Toronto company which is going to guide you through suitable basement preparation.

Our wet basement solutions in Toronto company offers best way to prevent issues with moisture

Moisture may be produced by hot air that leaks into a cold basement through rim joists. Gaps that surround the rim joist and sill plate are known for air leaks.

One objective while sealing gaps includes creating barriers against air and water intrusion. If you determine that you want to do the job on your own, utilize a low shrink sealant or approved mortar. While sealing around a cast in penetration which has a sleeve, like a water or gas line, you can seal the area between the sleeve and the service line.

Insulate the basement.

A few condensation problems caused by humidity may be addressed using an automatic dehumidifier, yet a better solution includes insulating the basement.

Utilize foam tubing that will insulate; it’ll help to keep condensation upon cool water pipes from dripping. However, do not do this one alone. In addition, insulate and run your dehumidifier.

Add perimeter drain.

Whether you take this project on yourself or have the contractor perform the job, the drain is going to collect all rising water and carry the water away from any foundation.

Be certain the perimeter drain gets protected from clogging and damage by surrounding it using gravel fill. Additionally, utilize a pipe which has an integrated filter sock that keeps out clay soils and silt.

Install sensors for observing purposes.

Water leaks may be detected before there is an issue with valve and floor sensors. A few sensors may turn power off and shut leaky valves off when they are tripped.

For correct landscaping, the foundation’s top ought to be a minimum of 8” above the soil in order to keep moisture from damaging the outside finish. Plants ought to be placed at least 2’ from the foundation, as well as low enough inside the soil so as not to direct ground water toward your foundation. Do not over water your ground while landscaping.

For more details on our wet basement solutions in Toronto contact Aquatech Waterproofing at 416-454-7575.

,

The Fundamentals of Basement Waterproofing

A challenge that many homeowners face is basement waterproofing. It creates a domino effect problem if not done in the right way. Basement waterproofing will allow you do many things in your basement, starting with having a usable basement for whatever purpose you may decide.

The time when the foundation is built is the best time to do waterproofing

Waterproofing when the foundation is built will make sure that it will last for a long time. Another reason why this is also the best time to do basement waterproofing is because it’s much easier to get into small spaces before they are closed off due to constructions, such as corners and even areas where drainage pipes will be installed. You have to give the basement a very thorough check before deciding how to do the basement waterproofing if your house is old. Contacting a professional is a wise thing to do when doing waterproofing so that you won’t need to do it all over again because the waterproofing was wrongly done.

Waterproofing can be done in two ways: external basement waterproofing and interior basement waterproofing. Tanking is one of the common methods of external waterproofing. Tanking is a process in which a bonding substance or membrane is applied to the outside walls of your basement. The tanking should be done as your home is being constructed, especially in cases where the basement is underground. The outside drainage system is another method of external waterproofing. In this method, your basement will be constructed in such a way that the basement floor slopes toward your home’s sump pump.

A plastic honeycomb membrane is applied to the walls and floor of your basement for quick removal of any moisture from your basement. Another method of external waterproofing is the French drain. This waterproofing method is usually installed on houses that are located in parts of the country where there are heavy levels of rainfall and other types of moisture-based weather. The International Building Code only recognizes external waterproofing method as efficient enough to keep water from doing any intense structural damage to a home or building.

Moisture is kept from making its way into your basement by interior waterproofing. A sealant is applied on the walls and floor of the basement to prevent water and moisture from seeping through. It also prevents the growth of molds and mildew. Technically, interior sealants aren’t materials for basement waterproofing, but they can help you make do while you are working on other waterproofing methods. It is recommended that you do both the external and interior waterproofing, for best results.

Your basement forms the foundation of your house and because of this, it is important to do waterproofing. If your basement is not in the best condition, your entire house can be jeopardized in the final analysis.